Cheat Engine

grasmanek94

here: http://www.youtube.com/watch?v=-qblhmzOJOM
so u can see what the problem is. this is my 3rd topic for this problem Sad

so i added a video to youtube for you all so you all can see what the problem is.
i say it now : because of the value changes to ?? i can search further for the pointer.

Dark Byte · Posted: Sat Aug 02, 2008 8:17 pm Post subject:

use find out what accesses

grasmanek94 · Posted: Sun Aug 03, 2008 1:05 pm Post subject: re

the same problem Sad

Dark Byte · Posted: Sun Aug 03, 2008 1:46 pm Post subject:

1: ignore the ??'s (but do use accesses)
if it's accessed it will be shown.

2: go to settings code finder and make sure to use debug registers

3: If all fails, try creating a new 4 byte value with only the base pointer address and find out what accesses that

-DEViL- · Posted: Mon Aug 04, 2008 12:47 am Post subject:

try "kernel mode debugger option"

grasmanek94 · Posted: Wed Aug 06, 2008 2:21 pm Post subject: re

ok thx for replieing i will try it now. and( ps. can u say me what realy means "hyper scan" ??) and the kernelmode .... is always enabled Wink

_________________
YEP. thx. making a new 4 bytes(but yeah if the value realy is float make it float ^^) adress works ^^.

hehe. finally.

and maybe you know how i can expand my knowledge about CE. i think i only can use 10% from what that prog realy can.

and is it possible to create nocd patches with CE ?

MRDB512 · Posted: Tue Aug 12, 2008 9:26 am Post subject: Re: re

grasmanek94 · Posted: Wed Aug 13, 2008 3:50 am Post subject: Re: re

MRDB512 · Posted: Thu Aug 14, 2008 2:25 am Post subject:

Well you dont want to use CE for that
cos CE is Memory only

you want to alter the main programs code

and by using CE all you would do is TEMP alter the Memory image of Program, to make it run with nocd

and then you would have to enable that long script every time you
play the game. Only Temp

Check out [Sheeps] tut, to learn more!

Start with old games to learn from
and then work on the new ones, cos of code Swapping, and debugger Detection!

grasmanek94 · Posted: Sun Aug 17, 2008 9:35 am Post subject: re

ej and in CE is a option called "size of scan buffer" so. i thout it makes scanning faster so i did set it to 100 000 kb xD then i had a error :s WTF happend?

Dark Byte · Posted: Sun Aug 17, 2008 10:13 am Post subject:

that means all your memory was used up.
512KB is usually good enough. It also depends on the cpu.
If your cpu has a big cache, a higher scanbuffer can increase the speed. But if you set it too big it may cause more misses and slow down

grasmanek94 · Posted: Mon Aug 18, 2008 1:58 am Post subject:

oh. hehe my cpu cache is 8 mb ^^

'; $_switch_quick_reply_count = (isset($this->_tpldata['switch_quick_reply'])) ? sizeof($this->_tpldata['switch_quick_reply']) : 0;for ($_switch_quick_reply_i = 0; $_switch_quick_reply_i < $_switch_quick_reply_count; $_switch_quick_reply_i++){ echo ' '; } // END switch_quick_reply echo '	' , ((isset($this->_tpldata['.'][0]['L_INDEX'])) ? $this->_tpldata['.'][0]['L_INDEX'] : '') , ' '; $_switch_parent_link_count = (isset($this->_tpldata['switch_parent_link'])) ? sizeof($this->_tpldata['switch_parent_link']) : 0;for ($_switch_parent_link_i = 0; $_switch_parent_link_i < $_switch_parent_link_count; $_switch_parent_link_i++){ echo ' -> ' , ((isset($this->_tpldata['.'][0]['PARENT_NAME'])) ? $this->_tpldata['.'][0]['PARENT_NAME'] : '') , ' '; } // END switch_parent_link echo ' -> ' , ((isset($this->_tpldata['.'][0]['FORUM_NAME'])) ? $this->_tpldata['.'][0]['FORUM_NAME'] : '') , '	' , ((isset($this->_tpldata['.'][0]['S_TIMEZONE'])) ? $this->_tpldata['.'][0]['S_TIMEZONE'] : '') , ' ' , ((isset($this->_tpldata['.'][0]['PAGINATION'])) ? $this->_tpldata['.'][0]['PAGINATION'] : '') , ' '; echo '
' , ((isset($this->_tpldata['.'][0]['PAGE_NUMBER'])) ? $this->_tpldata['.'][0]['PAGE_NUMBER'] : '') , '